Search Results

This paper presents a methodology of trajectory planning for the surrounding-aware lane change maneuver of autonomous vehicles based on a data-driven method. The lateral motion is planned by sampling candidate patterns which are defined based on quintic polynomial functions over time. Based on the cost evaluation among the sampled candidates, the optimal lateral motion pattern is selected as a reference and tracked by the controller. The longitudinal motion is planned and controlled using Model Predictive Control (MPC) which is an optimal control method designed considering the surrounding traffic information. To realize the lane change motion similar to the human driving behavior in the surrounding traffic situation, the human driving pattern is modeled in the form of motion parameters and considered in planning the lateral and longitudinal motion.

CW/CA (Collision Warning /Collision Avoidance) Systems have been an active research and development area as interests and demands for the advanced vehicle increase. A CW/CA ‘Hardware-in-the-Loop Simulation (HiLS)’ system has been designed and used to test a CW/CA algorithm, radar sensors, and warning displays under realistic operating conditions in the laboratory. A CW/CA algorithm has two parts. One is a distance decision algorithm that determines the critical warning and braking distance and the other is a brake control algorithm for collision avoidance. The CW/CA HiLS system consists of a controller in which a DSP chip is installed, a preceding vehicle simulator, a radar sensor and a warning display. The controller calculates velocities of the preceding and following vehicles, relative distance and relative velocity of the vehicles using vehicle simulation models. The relative distance and velocity are applied to the vehicle simulator that is controlled by a DC motor.

This paper presents an Interacting Multiple Model (IMM) based side slip angle estimation method to estimate side slip angle under various road conditions for vehicle stability control. Knowledge of the side slip angle is essential enhancing vehicle handling and stability. For the estimation of the side slip angles in previous researches, prior knowledge of tire parameters and road conditions have been employed, and sometimes additional sensors have been needed. These prior knowledge and additional sensors, however, necessitates many efforts and make an application of the estimation algorithm difficult. In this paper, side slip angle has been estimated using on-board vehicle sensors such as yaw rate and lateral acceleration sensors. The proposed estimation algorithm integrates the estimates from multiple Kalman filters based on the multiple models with different parameter set.

This paper proposes a rear-wheel steering control method that can modify and improve the vehicle lateral response without tire model and parameter. The proposed control algorithm is a combination of steady-state and transient control. The steady state control input is designed to modify steady-state yaw rate response of the vehicle, i.e. understeer gradient of the vehicle. The transient control input is a feedback control to improve the transient response when the vehicle lateral behavior builds up. The control algorithm has been investigated via computer simulations. Compared to classical control methods, the proposed algorithm shows good vehicle lateral response such as small overshoot and fast response. Specifically, the proposed algorithm can alleviate stair-shaped response of the lateral acceleration.

This paper describes a robust Model Predictive Control (MPC) framework of lane change for automated driving vehicles. In order to develop a safe lane change for automated driving, the driving mode and lane change direction are determined considering environmental information, sensor uncertainties, and collision risks. The safety margin is calculated using predicted trajectories of surround and subject vehicles. The MPC based combined steering and longitudinal acceleration control law has been designed with extended bicycle model over a finite time horizon. A reachable set of vehicle state is calculated on-line to guarantee that MPC state and input constraints are satisfied in the presence of disturbances and uncertainties. The performance of the proposed algorithm has been conducted simulation studies.

This paper represents a parking lot occupancy detection and parking control algorithm for the autonomous valet parking system. The parking lot occupancy detection algorithm determine the occupancy of the parking space, using LiDAR sensors mounted at each side of front bumper. Euclidean minimum spanning tree (EMST) method is used to cluster that information. After that, a global parking map, which includes all parking lots and access road, is constructed offline to figure out which cluster is located in a parking space. By doing this, searching for available parking lots has been finished. The proposed parking control algorithm consists of a reference path generation, a path tracking controller, and a parking process controller. At first, route points of the reference path are determined under the consideration of the minimum turning radius and minimum safety margin with near parking.

This paper describes a hierarchical motion planning and control framework for overtaking maneuvers under racing circumstances. Unlike urban or highway autonomous driving conditions, race track driving requires longer prediction and planning horizons in order to respond to upcoming corners at high speed. In addition, the subject vehicle should determine the optimal action among possible driving modes when opponent vehicles are present. In order to meet these requirements and secure real time performance, a hierarchical architecture for decision making, motion planning, and control for an autonomous racing vehicle is proposed. The supervisor determines whether the subject vehicle should stay behind the preceding vehicle or overtake, and its direction when overtaking. Next, a high level trajectory planner generates the desired path and velocity profile in a receding horizon fashion.

This paper describes vehicle stability control (VSC) scheme to prevent rollover and to improve both maneuverability and lateral stability by integrating individual chassis control modules such as electronic stability control (ESC), active front steering (AFS) and continuous damping control (CDC). The proposed VSC system consists of an upper and lower level controller. The upper level controller determines a control mode such as rollover mitigation, maneuverability and lateral stability, and it also calculate desired values for its objectives. The lower level controller determines longitudinal and lateral tire forces as inputs of each control modules such as the ESC and AFS. From the simulation results, it is shown that the proposed VSC system can prevent vehicle rollover, while at the same time improving both maneuverability and lateral stability

This paper presents a longitudinal control algorithm for an adaptive cruise control (ACC) with collision avoidance (CA) in multiple vehicle traffic situations. The proposed algorithm consists of a multi-target tracking filter, a primary target selection algorithm and an integrated ACC/CA system. The multi-target tracking filter is used to smooth the sensor signal, and makes it possible to apply to a control system. The primary target selection algorithm decides an in-lane target and provides the information to an integrated ACC/CA system in order to drive a subject vehicle smoothly and improve safety in complex traffic situations. Finally, the integrated ACC/CA system computes the desired acceleration. The performance and safety benefits of the multi-vehicle ACC/CA system is investigated via simulations using real data on driving. Simulation results show that the response of multi-vehicle ACC/CA system is more smooth and safer at a change of traffic situations.